1 ps7032i 12/12/12 truth table en in on switch 0 0 s 1 a , s 1 b , s 1 c , s 1 d 0 1 s 2 a , s 2 b , s2 c , s 2 d 1 x disabled features ? high-performance solution to switch between video sources ? wide bandwidth: 570 mhz (typical) ? low on-resistance: 5? (typical) ? low crosstalk at 10 mhz: C80db ? ultra-low quiescent power (0.1a typical) ? single supply operation: +5.0v ? fast switching: 10ns ? esd > 5kv hbm, 10kv i/o to gnd ? packaging (pb-free & green a vailable): C 16-pin 150-mil wide plastic soic (w) C 16-pin 150-mil wide plastic qsop (q) pi5v330s low on-resistance wideband/video quad 2-channel mux/demux block diagram description pericom semiconductor s pi5v330s is a true bidirectional quad 2-channel multip lexer/demultiplexer recommended for both rgb and composite video switching applications. the video switch can be driven from a current output ramdac or voltage output composite video source. low on-resistance and wide bandwidth make it ideal for video and other applications. also this device has exceptionally high current capability which is far greater than most analog switches of fered today . a single 5v supply is all that is required for operation. the pi5v330s of fers a high-performance, low-cost solution to s witch b etween v ideo s ources. t he a pplication s ection d escribes t he pi5v330s replacing the hc4053 multiplier and buffer/amplifer. pin confguration pin description pin name description s 1 a , s 1 b , s 1 c , s 1 d s 2 a , s 2 b , s 2 c , s 2 d analog v ideo i/o in select input en enable d a , d b d c , d d analog v ideo i/o gnd ground v dd power 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 v dd en s 1 d s 2 d d d s 1 c s 2 c d c in s 1 a s 2 a d a s 1 b s 2 b d b gnd s 1 a s 2 a s 1 b s 2 b s 1 c s 2 c s 1 d s 2 d d a d b d c d d en in decoder/drivers 13-0016
2 ps7032i 12/12/12 pi5v330s low on-resistance wideband/video quad 2-channel mux/demux storage t emperature ..........................................................C65c to +150c ambient t emperature with power applied .........................C40c to +85c supply v oltage to ground potential (inputs & v dd only) .. C0.5v to +7.0v supply v oltage to ground potential (outputs & d/o only) C0.5v to +7.0v dc input v oltage .................................................................. C0.5v to +7.0v dc output current ............................................................................. 120ma power dissipation ................................................................................. 0.5w note: stresses greater than those listed under maximum ra t- ings may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specifcation is not implied. ex - posure to absolute maximum rating conditions for extended periods may affect reliability. notes: 1. for max. or min. conditions, use appropriate value specifed under electrical characteristics for the applicable device type. 2. typical values are at v dd = 5.0v, t a = 25c ambient and maximum loading. 3. measured by the voltage drop between s1, s2, and d i/o pins at indicated current through the switch. on-resistance is determined by the lower of the voltages on the s1, s2, and d i/o pins. maximum ratings (above which the useful life may be impaired. for user guidelines, not tested.) dc electrical characteristics (over the operating range, t a = C40c to +85c, v dd = 5v 5%) parameters description test conditions (1) min. typ. (2) max. units v analog analog signal range 0 2.0 v v ih input high v oltage guaranteed logic high level 2.0 - v il input low v oltage guaranteed logic low level C0.5 0.8 i ih input high current v dd = max., v in = v dd 1 a i il input low current v dd = max., v in = gnd 1 i o analog output leakage current 0 s1, s2 or d v dd , switch off 1 v ik clamp diode v oltage v dd = min., i in = -18ma -0.7 -1.2 v v h input hysteresis at control pins 150 - mv r on switch on-resistance (3) v dd = min., v in = 1.0v, i on = 13ma 5 7 ? v dd = min., v in = 2.0v, i on = 26ma 7 10 13-0016
3 ps7032i 12/12/12 pi5v330s low on-resistance wideband/video quad 2-channel mux/demux power supply characteristics parameters description test conditions (1) min. typ (2) max. units i cc quiescent power supply current v dd = max. in = gnd or v dd 0.1 3.0 a ? icc supply current per input @ ttl high v dd = max. in = 3.4v (3) 2.5 ma i ccd supply current per input per mhz (4) v dd = max., s1, s2 and d pins open en = gnd control input t oggling 50% duty cycle 0.25 ma/ mhz notes: 1. for max. or min. conditions, use appropriate value specifed under electrical characteristics for the applicable device. 2. typical values are at v dd = 5.0v, +25c ambient. 3. per ttl driven input ( v in = 3.4v, control inputs only); s1, s2, and d pins do not contribute to i cc . 4. this current applies to the control inputs only and represent the current required to switch internal capacitance at the specifed frequency. the s1, s2, and d i/o pins generate no signifcant ac or dc currents as they transition. this parameter is not tested, but is guaranteed by design. notes: 1. this parameter is determined by device characterization but is not production tested. dynamic characteristics (over the operating range, t a = C40c to +85c, v dd = 5v 5%) parameters description test conditions min. typ. max. unit t on turn on t ime r l = 75?, c l = 20 pf , see fig. 4 2.5 5 ns t off turn off t ime r l = 75?, c l = 20 pf , see fig. 4 1.1 5 b w (1) -3 db bandwidth see fig. 5 570 mhz x talk crosstalk 10mhz, see fig. 5, c l = 0pf -80 db c in (1) input/enable capacitance v in = 0v, f = 1 mhz 6 pf c off (1) capacitance, switch off v in = 0v, f = 1 mhz 6 c on (1) capacitance, switch on v in = 0v, f = 1 mhz 9 o irr off isolation 10mhz, see fig 5, c l = 0pf -48 db 13-0016
4 ps7032i 12/12/12 pi5v330s low on-resistance wideband/video quad 2-channel mux/demux defnitions symbol description r on resistance between source and drain with switch in the on state. i o output leakage current measured at s1, s2, and d with the switch off. v in digital voltage at the in pin that selects between s1 and s2 analog inputs. v en a voltage that enables the chip. c in capacitance at the digital inputs. c off capacitance at analog i/o (s1, s2, d) with switch off. c on capacitance at analog i/o (s1, s2, d) with switch on. v ih minimum input voltage for logic high. v il minimum input voltage for logic low. i ih (i il ) input current of the digital input. t on propagation delay measured between 50% of the digital input to 90% of the analog output when switch is turned on. the peak analog voltage is 0.714v. t off propagation delay measured between 50% of the digital input to 90% of the analog output when switch is turned off. the peak analog voltage is 0.714v. b w frequency response of the switch in the on state measured at 3db down. x talk is an unwanted signal coupled from channel to channel. measured in Cdb. x ta lk = 20 log v ou t /v in . this is non-adjacent crosstalk. o irr off isolation is the resistance (measured in Cdb) between the input and output with the switch off (no). 13-0016
5 ps7032i 12/12/12 pi5v330s low on-resistance wideband/video quad 2-channel mux/demux figure 1. gain vs frequency figure 2. off isolation vs frequency 13-0016
6 ps7032i 12/12/12 pi5v330s low on-resistance wideband/video quad 2-channel mux/demux figure 3. crosstalk vs frequency figure 4. switching time t on t off 90% 90% 50% analog output digital input 50% 75 gnd en in 3v s d +5.0v v dd v out 20pf figure 5. gain/phase, crosstalk, off-isolation pi5v330s t1 r1 s1 hp11667a hp4396b 13-0016
7 ps7032i 12/12/12 pi5v330s low on-resistance wideband/video quad 2-channel mux/demux packaging mechanical: 16-pin soic (w) description: 16-pin, 150mil wide soic package code: w document control #: revision: f date: 06 /15/12 date: 06 /15/12 pd-1004 2012-0398 13-0016
8 ps7032i 12/12/12 pi5v330s low on-resistance wideband/video quad 2-channel mux/demux packaging mechanical: 16-pin qsop (q) 1 .189 .197 .053 .069 .004 .010 seating plane .025 bsc .007 .010 .228 .244 1 16 .150 .157 x.xx x.xx denotes dimensions in millimeters 0.635 4.80 5.00 1.35 1.75 5.79 6.19 0.101 0.254 .008 .012 0.203 0.305 3.81 3.99 0.178 0.254 0.38 .008 0.203 .015 x 45 ref detail a detail a .008 0.20 min. guage plane .010 0.254 .041 1.04 ref .016 .035 0.41 0.89 0?-6? .008 .013 0.20 0.33 description: 16-pin 150-mil wide qsop package code: q document control no. pd - 1201 revision: g date: 11/07/07 note: 1) controlling dimensions in inches. 2) ref: jedec mo-137b/ab. 3) dimensions do not include mold flash, protrusions or gate burrs pericom semiconductor corporation 3545 n. 1st street, san jose, ca 95134 1-800-435-2335 ? www.pericom.com ordering information ordering code package code package description pi5v330swe w pb-free & green, 16-pin 150-mil wide plastic soic PI5V330SQE q pb-free & green, 16-pin 150-mil wide plastic qsop notes: 1. thermal characteristics can be found on the company web site at www.pericom.com/packaging/ 2. e = pb-free and green 3. adding an x suffx = t ape/reel pericom semiconductor corporation ? 1-800-435-2336 ? www .pericom.com 13-0016
|
